3D Printing

Limbo lower now: 3D-printed STAR bot flattens itself to crawl under doorways

Limbo lower now: 3D-printed STAR bot flattens itself to crawl under doorways
Students at UC Berkeley have developed the STAR, a 3D-printed robot that flattens its legs to slip under small spaces and raises them up again to climb over obstacles
Students at UC Berkeley have developed the STAR, a 3D-printed robot that flattens its legs to slip under small spaces and raises them up again to climb over obstacles
View 5 Images
Depending on the angle, the robot can move faster over different surfaces, climb over taller objects, or slip into narrow passageways, among other tasks
1/5
Depending on the angle, the robot can move faster over different surfaces, climb over taller objects, or slip into narrow passageways, among other tasks
Students at UC Berkeley have developed the STAR, a 3D-printed robot that flattens its legs to slip under small spaces and raises them up again to climb over obstacles
2/5
Students at UC Berkeley have developed the STAR, a 3D-printed robot that flattens its legs to slip under small spaces and raises them up again to climb over obstacles
At a sprawl angle of zero degrees, the robot lays flat on the ground and has a height of just 2.5 cm (1 in), with a length of only 12 cm (4.7 in) and a width of 11 cm (4.3 in)
3/5
At a sprawl angle of zero degrees, the robot lays flat on the ground and has a height of just 2.5 cm (1 in), with a length of only 12 cm (4.7 in) and a width of 11 cm (4.3 in)
Each of the legs has three spokes measuring 2.8 cm (1.1 in) with a 90-degree gap between them, which allow it to crawl over obstacles 4 cm (1.6 in) higher than if it just had wheels
4/5
Each of the legs has three spokes measuring 2.8 cm (1.1 in) with a 90-degree gap between them, which allow it to crawl over obstacles 4 cm (1.6 in) higher than if it just had wheels
At a 90-degree sprawl, the robot can fit through smaller vertical spaces and travel over rough terrain more easily
5/5
At a 90-degree sprawl, the robot can fit through smaller vertical spaces and travel over rough terrain more easily
View gallery - 5 images

Nature has been the source of inspiration for a variety of different forms of robotic locomotion. Yet another example is the STAR, a 3D-printed robot modeled after an insect's ability to squeeze into even the tiniest spaces. Developed by students at UC Berkeley's Biomimetic Millisystems Lab the STAR, which stands for Sprawl Tuned Autonomous Robot, is able to flatten its legs down to slip under a small gap and then raise them up again to climb over larger obstacles.

With the exception of the electronics, each component of the STAR was built using a ProJet 3000 3D printer, meaning a full robot can be manufactured quickly and cheaply. The main core of the bot holds its control board and battery, which are connected to the six individual legs that propel it forward. Each of the legs has three spokes measuring 2.8 cm (1.1 in) with a 90-degree gap between them, which allow it to crawl over obstacles 4 cm (1.6 in) higher than if it just had wheels.

A brushed DC motor provides motion to each set of legs, while a 300 mA/hr LiPo 4V battery gives it enough power to run at full speed for 30 minutes on a single charge. Altogether, the tiny robot weighs just 73 g (2.6 oz).

What really sets the STAR apart from other robots, though, is its ability to adjust its sprawl angle (i.e. the angle between its body and legs) over a range of 150 degrees to adapt to different situations. Depending on the angle, the robot can move faster over different surfaces, climb over taller objects, or slip into narrow passageways, among other tasks.

At a sprawl angle of zero degrees, the robot lays flat on the ground and has a height of just 2.5 cm (1 in), with a length of only 12 cm (4.7 in) and a width of 11 cm (4.3 in)
At a sprawl angle of zero degrees, the robot lays flat on the ground and has a height of just 2.5 cm (1 in), with a length of only 12 cm (4.7 in) and a width of 11 cm (4.3 in)

At a sprawl angle of zero degrees, the robot lays flat on the ground and has a height of just 2.5 cm (1 in), a length of only 12 cm (4.7 in) and a width of 11 cm (4.3 in). It can't actually move in this position, but by changing its sprawl just a few degrees, the robot's legs can touch the ground to move underneath an obstacle, such as a door, without gaining much height. At a 90-degree sprawl, the robot can fit through smaller vertical spaces and travel over rough terrain more easily.

Changing the sprawl also allows the bot to recover from a fall no matter how it lands, since it can maneuver its legs to flip itself over when needed. The robot can also reverse its direction just by raising its legs into a negative sprawl angle and touching the opposite sides to the ground.

Each of the legs has three spokes measuring 2.8 cm (1.1 in) with a 90-degree gap between them, which allow it to crawl over obstacles 4 cm (1.6 in) higher than if it just had wheels
Each of the legs has three spokes measuring 2.8 cm (1.1 in) with a 90-degree gap between them, which allow it to crawl over obstacles 4 cm (1.6 in) higher than if it just had wheels

The STAR's ability to limbo under doorways and scale obstacles would be impressive enough, but the research team found that changing the sprawl angle even affected its overall velocity. When running on a lower sprawl angle, the robot's body remained more stable and the legs contacted the ground with more force, giving it a slight speed boost.

On a smooth, flat surface, the STAR is capable of running along the ground at a speedy 5.2 m/s (approx. 11.6 mph), leaving its lab stablemate, the VelociRoACH, eating its dust. By only spinning one side of legs at maximum speed, the robot can also turn a full 360 degrees in under a second and take off in another direction almost instantly.

The team has already made three versions of the STAR and added slight improvements to the design with each new model. The latest iteration sports a handful of mechanical tweaks along with fiber-reinforced rods that should prevent damage when the robot crashes at high speeds.

You really have to see the STAR in action to understand just how maneuverable it is, so check out the video below to see it glide underneath short gaps and then quickly take off running while barely breaking stride.

Source: Biomimetic Millisystems Lab

Acrobatics of STAR.V3 , UC Berkeley, a high speed 3D printed robot.

View gallery - 5 images
2 comments
2 comments
Anne Ominous
I don't understand how this is any more of a "robot" than any other remotely-controlled device.
I appreciate the fact that it is a research project, but by the logic that seems to be used here, the remotely-controlled mouse I use to play with my pet is a robot.
Jay Finke
Wow that's creepy and it's fast too. I might have nightmares about this thing, just imagine one of these the size of a car. nice build however